Packages in the electronics directory

Last updated: Thu Mar 20 04:24:06 1997

x10-automate

*download (96 Kb)
Version: 1.00-1 Last modified: Wed Mar 19 22:59:19 1997
Architecture: i386
Maintainer:
Mark W. Eichin <eichin@kitten.gen.ma.us>
Description:
GUI interface for x10 power line control utility Tk (wish) based GUI for the "x10" home-control program.

With this program you can attach icons to your various X10 devices and see them displayed on a toolbar as well as a floorplan of your own. You can also read, write and edit programs to download to the CP-290 controller.

Depends:
x10, tk40 | tk41 | tk42

x10

*download (17 Kb)
Version: 1.05-1 Last modified: Thu Feb 27 17:58:58 1997
Architecture: i386
Maintainer:
Mark W. Eichin <eichin@kitten.gen.ma.us>
Description:
Operate X-10 electrical power control modules. X-10 modules are devices that plug into an electrical outlet and allow you to remotely control the power to a lamp or an appliance that is plugged into them. There are also X-10 modules that install in place of wall switches to control lights, and there's one that can be used to set back a thermostat.

This program commands up to 256 X-10 modules via a CP-290 serial-interface controller plugged into any serial port of your system. You can use it to automate your home! It's also commonly used to provide control over computers and other devices that might need to be powered up or down via a timed command or remote control. The CP-290 controller stores 128 clock-driven events that it will execute when your computer is turned off, so you can even program your computer to turn itself on at a particular time.

You can buy the modules and manual controllers in Radio Shack stores, but the CP-290 serial-interface controller used to command them using your Debian system is slightly harder to find. Instructions on where to order one are included in the documentation of this package.

Depends:
libc5 (>= 5.4.0-0), libg++27 (>= 2.7.2.1-1)

nitpic

*download (100 Kb)
Version: 0.1-1 Last modified: Tue Feb 25 16:50:57 1997
Architecture: i386
Maintainer:
Klee Dienes <klee@debian.org>
Description:
Simulator for the Microchip PIC16C84 Microcontroller An X-based simulator for the Microchip PIC family of microcontrollers. Currently supports the PIC16C84 only.
Depends:
libc5 (>= 5.4.0-0), xlib6 (>= 3.2-0)

acs

*download (214 Kb)
Version: 021-2 Last modified: Mon Feb 3 16:50:43 1997
Architecture: m68k
Maintainer:
Jonathan K. Rabone <jkr@debian.org>
Description:
Al's Circuit Simulator ACS is a general purpose circuit simulator. It performs nonlinear dc and transient analyses, fourier analysis, and ac analysis linearized at an operating point. It is fully interactive and command driven. It can also be run in batch mode or as a server. The output is produced as it simulates. Spice compatible models for the MOSFET (level 1,2,3) and diode are included in this release.
Depends:
libc5 (>= 5.4.0-0)

acs

*download (220 Kb)
Version: 021-2 Last modified: Thu Jan 30 07:51:09 1997
Architecture: i386
Maintainer:
Jonathan K. Rabone <jkr@debian.org>
Description:
Al's Circuit Simulator ACS is a general purpose circuit simulator. It performs nonlinear dc and transient analyses, fourier analysis, and ac analysis linearized at an operating point. It is fully interactive and command driven. It can also be run in batch mode or as a server. The output is produced as it simulates. Spice compatible models for the MOSFET (level 1,2,3) and diode are included in this release.
Depends:
libc5 (>= 5.4.17-1), libg++27 (>= 2.7.2.1-1)

pcb

*download (229 Kb)
Version: 1.4.3-1 Last modified: Wed Jan 1 09:59:02 1997
Architecture: m68k
Maintainer:
Michael Mattice <mattice@mattice.reslife.okstate.edu>
Description:
Printed Circuit Board Design Program
Depends:
elf-x11r6lib, libc5 (>= 5.2.18)

pcb

*download (233 Kb)
Version: 1.4.3-1 Last modified: Mon Dec 2 10:04:25 1996
Architecture: i386
Maintainer:
Michael Mattice <mattice@mattice.reslife.okstate.edu>
Description:
Printed Circuit Board Design Program
Depends:
elf-x11r6lib, libc5 (>= 5.4.7-7)